desktop hard drive xbox image
Austin
I bought a hard drive offline, and a xbox 360 hard drive housing unit separately. I put them together, and inserted it into the xbox. When I go to storage devices it doesn't show the hard drive. Is there something I have to do to get the xbox to recognize it?
Does the hard drive have to have a partition on it that the xbox can then format maybe?
Answer
ok if it aint western digital hard drive there is no way to format it for the xbox 360 console but if it is u would need these items:
(1) a spair sata cable
(2) a desktop pc windows prefered
(3) half a brain to conect the hard drive to the pc
(4) u need the right HDDSS.bin file
(5) u need HddHackr_v1.22_Build_20091022
(6) a flash drive
then u need to know how to use the hdd hacker
HddHacker supports two flashing modes, Auto and Manual. Typing HddHackr at a DOS prompt
will start auto mode. In auto mode all hard drives will be detected automatically.
In manual mode you can enter all the parameters used for flashing by hand.
The following help screen is displayed if you start HddHacker with a wrong number of
arguments:
HDDHACKR [C|D|F|R] [PORT] [DRIVE POS] [SECTOR FILE] [RESTORE FILE]
C: Create Partitions 0/2/3
D: Dump sector 16-22 from XBOX360 HDD to file
F: Flash Western Digital firmware
R: Restore Western Digital firmware
PORT: Port to send command to e.g. 09F0
DRIVE POS: A0 for Master, B0 for Slave
SECTOR FILE: Sector dump file e.g. HDDSS.BIN
RESTORE FILE: Firmware restore file e.g. UNDO.BIN
Example for create, dump, flash and restore:
HDDHACKR C 09F0 A0
HDDHACKR D 09F0 A0 HDDSS.BIN
HDDHACKR F 09F0 A0 HDDSS.BIN UNDO.BIN
HDDHACKR R 09F0 A0 UNDO.BIN
Explanation of the Parameters
-------------------------------
[C|D|F|R]
---------
- this will set the mode of operation, it is recommended to first try to dump the XBOX360
hard drive data, if the dump will fail, it is highly unlikely that a flash or restore
will succeed on the Western Digital drive
[PORT]
--------
- the port to which the Hard Drive is connected, a port number should always be entered
in hexadecimal and have 4 hex digits, valid ports are: 01F0, 09F0, .....
- this option can be used if your PCI adapter card or on board SATA ports are
not identified by the auto mode
[DRIVE POS]
-------------
- on SATA ports this value is always A0, cause you can only connect a master drive to
a SATA port, so for SATA you will always type A0 here
[SECTOR FILE]
---------------
- name of the sector 16-22 dump file better known as HDDSS.BIN
[RESTORE FILE]
----------------
- name of the firmware restore file e.g. UNDO.BIN
Using HddHacker in manual mode
--------------------------------
* Dumping the HDDSS.BIN file *
Boot to MS-DOS from a writeable medium (like a floppy or UBS Stick).
Connect an *original* Xbox360 HDD to your SATA controller. Make sure it is the only
SATA device that is connected. Now run 'HDDHACKR D [PORT] A0 HDDSS.BIN' and it will create
the file 'HDDSS.BIN' and save it to the path you've started HddHacker from.
* Creating Partitions 0/2/3 *
In auto-mode the Partition 0/2/3 will be created automaticly to make the drive compatible
with "Xplorer360" and XBOX360 Console. In manual-mode you have to type 'HDDHACKR C [PORT] A0'.
* Flashing your Western Digital drive *
Turn off your PC and connect the Western Digital hard drive. Boot to MS-DOS again.
Type 'HDDHACKR F [PORT] A0 HDDSS.BIN UNDO.BIN' from the same path you have saved the HDDSS.BIN
file to. This will create an 'UNDO.BIN' file that you need if you want to undo the hack
and flash your firmware back to the original state.
* Restoring your WD to original state *
If you don't want to use your modded WD HDD in your XBOX360 anymore and you want to
flash it back to its original size/state, then you can now do so. Boot to MS-DOS and
run 'HDDHACKR R [PORT] A0 UNDO.BIN'. This will use the UNDO.BIN file you created before to
restore the drive to its original state.
* Vendor Intro Power Brute for misflashed drives *
To enter the recovery mode you should boot to MS-DOS, connect your hard drive to PC and type
'HDDHACKR R [PORT] A0 UNDO.BIN'. If the hard drive is misflashed you will be prompted with:
"Western Digital Vendor Intro failed on port [PORT]"
"Do you want to resend the command until the drive responds (Y/N)?"
Press YES, disconnect the hard drive from power and connect it again.
You should get Status 0x50 and the drive will be reflashed.
ok if it aint western digital hard drive there is no way to format it for the xbox 360 console but if it is u would need these items:
(1) a spair sata cable
(2) a desktop pc windows prefered
(3) half a brain to conect the hard drive to the pc
(4) u need the right HDDSS.bin file
(5) u need HddHackr_v1.22_Build_20091022
(6) a flash drive
then u need to know how to use the hdd hacker
HddHacker supports two flashing modes, Auto and Manual. Typing HddHackr at a DOS prompt
will start auto mode. In auto mode all hard drives will be detected automatically.
In manual mode you can enter all the parameters used for flashing by hand.
The following help screen is displayed if you start HddHacker with a wrong number of
arguments:
HDDHACKR [C|D|F|R] [PORT] [DRIVE POS] [SECTOR FILE] [RESTORE FILE]
C: Create Partitions 0/2/3
D: Dump sector 16-22 from XBOX360 HDD to file
F: Flash Western Digital firmware
R: Restore Western Digital firmware
PORT: Port to send command to e.g. 09F0
DRIVE POS: A0 for Master, B0 for Slave
SECTOR FILE: Sector dump file e.g. HDDSS.BIN
RESTORE FILE: Firmware restore file e.g. UNDO.BIN
Example for create, dump, flash and restore:
HDDHACKR C 09F0 A0
HDDHACKR D 09F0 A0 HDDSS.BIN
HDDHACKR F 09F0 A0 HDDSS.BIN UNDO.BIN
HDDHACKR R 09F0 A0 UNDO.BIN
Explanation of the Parameters
-------------------------------
[C|D|F|R]
---------
- this will set the mode of operation, it is recommended to first try to dump the XBOX360
hard drive data, if the dump will fail, it is highly unlikely that a flash or restore
will succeed on the Western Digital drive
[PORT]
--------
- the port to which the Hard Drive is connected, a port number should always be entered
in hexadecimal and have 4 hex digits, valid ports are: 01F0, 09F0, .....
- this option can be used if your PCI adapter card or on board SATA ports are
not identified by the auto mode
[DRIVE POS]
-------------
- on SATA ports this value is always A0, cause you can only connect a master drive to
a SATA port, so for SATA you will always type A0 here
[SECTOR FILE]
---------------
- name of the sector 16-22 dump file better known as HDDSS.BIN
[RESTORE FILE]
----------------
- name of the firmware restore file e.g. UNDO.BIN
Using HddHacker in manual mode
--------------------------------
* Dumping the HDDSS.BIN file *
Boot to MS-DOS from a writeable medium (like a floppy or UBS Stick).
Connect an *original* Xbox360 HDD to your SATA controller. Make sure it is the only
SATA device that is connected. Now run 'HDDHACKR D [PORT] A0 HDDSS.BIN' and it will create
the file 'HDDSS.BIN' and save it to the path you've started HddHacker from.
* Creating Partitions 0/2/3 *
In auto-mode the Partition 0/2/3 will be created automaticly to make the drive compatible
with "Xplorer360" and XBOX360 Console. In manual-mode you have to type 'HDDHACKR C [PORT] A0'.
* Flashing your Western Digital drive *
Turn off your PC and connect the Western Digital hard drive. Boot to MS-DOS again.
Type 'HDDHACKR F [PORT] A0 HDDSS.BIN UNDO.BIN' from the same path you have saved the HDDSS.BIN
file to. This will create an 'UNDO.BIN' file that you need if you want to undo the hack
and flash your firmware back to the original state.
* Restoring your WD to original state *
If you don't want to use your modded WD HDD in your XBOX360 anymore and you want to
flash it back to its original size/state, then you can now do so. Boot to MS-DOS and
run 'HDDHACKR R [PORT] A0 UNDO.BIN'. This will use the UNDO.BIN file you created before to
restore the drive to its original state.
* Vendor Intro Power Brute for misflashed drives *
To enter the recovery mode you should boot to MS-DOS, connect your hard drive to PC and type
'HDDHACKR R [PORT] A0 UNDO.BIN'. If the hard drive is misflashed you will be prompted with:
"Western Digital Vendor Intro failed on port [PORT]"
"Do you want to resend the command until the drive responds (Y/N)?"
Press YES, disconnect the hard drive from power and connect it again.
You should get Status 0x50 and the drive will be reflashed.
How can I transfer Xbox 360 save files from my computer onto my xbox hard drive?
lambolover
I have my xbox 360 save files on my desktop. How, specifically, can I get them onto my new xbox hard drive? Please help!
Answer
Well, You can use a Usb or a transfer cable. I have done this with multiple files before. Be sure you make backup of the files that you are transferring in case something happens.
Well, You can use a Usb or a transfer cable. I have done this with multiple files before. Be sure you make backup of the files that you are transferring in case something happens.
Powered by Yahoo! Answers
Tidak ada komentar:
Posting Komentar